Aries-automotive 5053 Manual de usuario descargar pdf

Page 1 of 2 6/20/07 (AM)

PARTS LIST:

1 Grille Guard 6

12-1.75mm x 35mm Hex Head Bolts

Driver/Left Mounting Bracket (A)

6 12mm Nylock Nuts

Passenger/Right Mounting Bracket (B)

12 12mm ID x 29mm OD x 3mm Flat Washers

Driver/Left Top Bracket (C)

10-1.50mm x 25mm Button Head Bolts

Passenger/Right Top Bracket (D)

2 10mm Nylock Nuts

4 10mm ID x 21mm OD x 1.5mm Flat Washers

PROCEDURE:

1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS

CAREFULLY BEFORE STARTING INSTALLATION. DO NOT ATTEMPT INSTALLATION ALONE;

PERSONAL INJURY OR DAMAGE TO THE TRUCK MAY RESULT.

Proceed to Step 5 if vehicle is equipped with factory hooks

2. Locate the square shape area underneath the front color bumper (Figure 1). Carefully drill a hole on each corner

of the marked area to be cut. Use a small tooth saw to cut from hole to hole.

3. Once you cut this area, locate the two factory nuts right above the cutout area and remove them from vehicle

(Figure 2).

4. Repeat steps 2 & 3 for opposite side, then proceed to Step 6

5. Locate and remove the factory tow hooks from vehicle. NOTE: You will not be reinstalling the tow hooks back to

the vehicle.

6. Partially hang driver side Mounting Bracket to the two factory bolts previously holding the tow hook (Figure 3).

Repeat this step for passenger side Mounting Bracket.

7. Open the hood and remove the plastic shroud covering the radiator (Figure 4).

8. Locate one factory bolt on each side in the inner fender support and remove (Figure 5). NOTE: You may remove

the four factory bolts across the top on the grille shell and gently pull towards the front of the vehicle to gain

access behind the grille shell.

9. Insert the driver side Top Bracket trough the bottom grille opening. Orient Top Bracket to the previously remove

bolt mounting location. Secure Top Bracket with factory bolt removed in step 8 (Figure 5 & 6)).

10. With help position Grille Guard on the inner side of Mounting Brackets. Attach Grille Guard to Mounting Brackets

using the included (6) 12mm x 35mm Hex Head Bolts, (6) 12mm Nylock Nuts, and (12) 12mm Flat Washers

(Figure 7). Do not tighten at this time.

11. Attach Top Bracket to the inner side of the vertical plate using the included (2) 10mm x 25mm Button Head Bolts,

(2) 10mm Nylock Nuts, (4) 10mm Flat Washers (Figure 6). Do not tighten at this time.

12. Level and align Grille Guard; and then tighten all hardware at this time.

13. Re-install plastic shroud back to the vehicle.

14. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

INSTALLATION INSTRUCTIONS

GRILE GUARD PART #5053-2/5053

07 DODGE DURANGO

(A) (B)

Cut this

marked area

Remove these

factory nuts

Figure 1 Figure 2

1 2

Indice de contenidos

Pagina 1 - INSTALLATION INSTRUCTIONS

Page 1 of 2 6/20/07 (AM) PARTS LIST: 1 Grille Guard 6 12-1.75mm x 35mm Hex He

Pagina 2 - Figure 7 Figure 8

Page 2 of 2 6/20/07 (AM) Mounting Bracket

Modelos relacionados 5053-2

Comentarios a estos manuales

Sin comentarios

Aries-automotive 5053 Manual de usuario

Busca en linea o descarga Manual de usuario para Para El Coche Aries-automotive 5053. Aries Automotive 5053 User Manual [ru] Manual de usuario

Indice de contenidos

Modelos relacionados 5053-2

Comentarios a estos manuales

Relacionado con productos y manuales para Para El Coche Aries-automotive 5053